Products in Adhesives & Sealants: Polyolefins

AGC Chemicals Americas, Inc. Fluon® ETFE C-88AXMP is a melt-processable copolymer of tetrafluoroethylene and ethylene that offers a unique combination of properties such as high resistance to heat and chemical attack and exceptional physical toughness. It can be processed using conventional methods like extrusion, injection molding, rotomolding, rotolining, and electrostatic coating and is available in the form of 1/8 inch pellets.

AGC Chemicals Americas, Inc. Fluon® ETFE C-55AP is a melt-processable copolymer of tetrafluoroethylene and ethylene that offers a unique combination of properties such as high resistance to heat and chemical attack and exceptional physical toughness. It can be processed using conventional methods like extrusion, injection molding, rotomolding, rotolining, and electrostatic coating and is available in the form of 1/8 inch pellets.

AGC Chemicals Americas, Inc. Fluon® ETFE C88AXMP-HT is a high-performance melt-processable copolymer of tetrafluoroethylene and ethylene that is designed for use in automotive applications. It offers improved thermal stability and performs better at higher temperatures than standard ETFE, with a maximum operating temperature of 200ºC. Its enhanced stress crack resistance, abrasion resistance, and mechanical strength make it suitable for ultra-thin layer insulation in vehicles and aircraft where reducing carbon footprint and increasing fuel efficiency is important.

AGC Chemicals Americas, Inc. Fluon® ETFE C-88AXP is a melt-processable copolymer of tetrafluoroethylene and ethylene that offers a unique combination of properties such as high resistance to heat and chemical attack and exceptional physical toughness. It can be processed using conventional methods like extrusion, injection molding, rotomolding, rotolining, and electrostatic coating and is available in the form of 1/8 inch pellets.

AGC Chemicals Americas, Inc. Fluon® ETFE C-55AXP is a melt-processable copolymer of tetrafluoroethylene and ethylene that offers a unique combination of properties such as high resistance to heat and chemical attack and exceptional physical toughness. It can be processed using conventional methods like extrusion, injection molding, rotomolding, rotolining, and electrostatic coating and is available in the form of 1/8 inch pellets.

UMEX products are a series of acid modified low-molecular-weight polyolefin containing a carboxylic anhydride group as the functional group. These products have a higher degree of modification and lower melt viscosity compared with conventional acid modified polyolefin. Therefore, the reactivity of the products is extremely adaptable to various synthetic resins and inorganic materials.

UMEX products are a series of acid modified low-molecular-weight polyolefin containing a carboxylic anhydride group as the functional group. These products have a higher degree of modification and lower melt viscosity compared with conventional acid modified polyolefin. Therefore, the reactivity of the products is extremely adaptable to various synthetic resins and inorganic materials.

UMEX 5200 is a specially-developed acid modified low-molecular-weight polypropylene. This product has a higher degree of modification and lower melt viscosity compared with conventional acid modified polypropylene. Therefore, polyolefin blended with the products excels in dispersibility of both pigments and fillers in resins, readily adheres to other materials. Moreover, this product works exceedingly well for improving molding processability of various resins.

UMEX products are a series of acid modified low-molecular-weight polyolefin containing a carboxylic anhydride group as the functional group. These products have a higher degree of modification and lower melt viscosity compared with conventional acid modified polyolefin. Therefore, the reactivity of the products is extremely adaptable to various synthetic resins and inorganic materials.

UMEX products are a series of acid modified low-molecular-weight polyolefin containing a carboxylic anhydride group as the functional group. These products have a higher degree of modification and lower melt viscosity compared with conventional acid modified polyolefin. Therefore, the reactivity of the products is extremely adaptable to various synthetic resins and inorganic materials.

CAPXIDAN® HD is a Modified Copolymer produced with a proprietary, specialized formulation. It is designed to be coextruded over Wood-Plastic Composite (WPC) deck boards to provide moisture, stain, wear resistance,esthetics, durability at elevated temperatures, and unprecedented adhesion to the WPC substrate. CAPXIDAN® HD is a two-component capstock system. The CAPXIDAN® resin should be extruded together with a specific synergistic additive masterbatch in the recommended proportion of 98:2 by weight.

PROPOLDER™ FPP4010 is polypropylene (PP) homopolymer in fine particle powder form. Unlike waxes, these higher molecular weight materials exhibit high toughness. PROPOLDER™ homopolymer PP materials are pure polypropylene with broad regulatory compliance and contain no residual chemicals or additives that may interfere with some application requirements.

PROPOLDER™ FPP4040 is polypropylene (PP) homopolymer in fine particle powder form. Unlike waxes, these higher molecular weight materials exhibit high toughness. PROPOLDER™ homopolymer PP materials are pure polypropylene with broad regulatory compliance and contain no residual chemicals or additives that may interfere with some application requirements.

Tasnee LD 1925F is a Low Density Polyethylene with a Melt Flow Rate of 2.0 g/10min (190°C/2.16 kg). Tasnee LD 1925F is mainly recommended for crosslinked and non-crosslinked foam applications. It designed to provide uniform cell distribution during LDPE foam extrusion process. Special additive package is used to control the foam cell structure so that uniform cell size and distribution occurred during foam extrusion process. It has a suitable molecular structure and special additive package for providing control and uniform foam cell structure and excellent mechanical properties to the foam. Tasnee LD 1925F can be easily processed on all types of LDPE foam extrusion equipment. The melt temperature is recommended to be in the range of 160 - 200°C.

Tasnee PP H3080 is a Polypropylene Homopolymer with a Melt Flow Rate (MFR) of 8 g/10min. Tasnee PP H3080 is designed for cast polypropylene (CPP) film, both for metallization and general purpose applications with excellent processability characteristics. Cast film produced by Tasnee PP H3080 offers excellent transparency, gloss and high stiffness.

PROPOLDER™ FPP4060 is polypropylene (PP) homopolymer in fine particle powder form. Unlike waxes, these higher molecular weight materials exhibit high toughness. PROPOLDER™ homopolymer PP materials are pure polypropylene with broad regulatory compliance and contain no residual chemicals or additives that may interfere with some application requirements.

S-368-N5T is a stable water dispersible grade of synthetic wax showing melting peaks ranging from 93 – 106°C. S-368 N5T imparts lubricity, abrasion resistance and anti-blocking properties to aqueous-based systems. It also has been used successfully in laminating adhesives to improve die-cutting performance.

AdvaBond ® 7411 is a chlorine-free low molecular weight anhydrous amine-modified polyolefin. Adva-Bond® 7411 is an effective adhesion promoter to low surface energy substrates, between different types of plastics which normally would separate and between plastics and polar substrates.

PROPOLDER™ FPP4020 is polypropylene (PP) homopolymer in fine particle powder form. Unlike waxes, these higher molecular weight materials exhibit high toughness. PROPOLDER™ homopolymer PP materials are pure polypropylene with broad regulatory compliance and contain no residual chemicals or additives that may interfere with some application requirements.

CAPXIDAN® LG is a modified copolymer produced with a proprietary, patent pending formulation. It is designed to be coextruded over Wood-Plastic Composite (WPC) deckboards to provide moisture, stain and wear resistance, esthetics, low gloss, durability at elevated temperatures, and unprecedented adhesion to the WPC substrate. CAPXIDAN® LG is a two-component capstock system. The CAPXIDAN® resin should be extruded together with a specific synergistic additive masterbatch in the recommended proportion of 98:2 by weight.

SAHARA H 034EM is a polypropylene homopolymer used for extrusion and thermoforming applications. This product is formulated with a low water-carry-over additive package.

FluoroGrip® F (HD-FEP) Teflon® is made from high molecular weight resin for applications where chemical resistance, high flex life and stress-crack-resistant performance are required.

DISPARLON® NS-30 is a patented blend of polyolefin with amide in xylene in paste form. This product effectively prevents sagging and settling of solvent-based coatings including those containing anti-corrosive pigments at high concentrations. NS-30 has little effect on viscosity, while still imparting strong anti-sagging/anti-settling properties.

Tasnee PP H3030 is a Polypropylene Homopolymer with a Melt Flow Rate (MFR) of 3.0 g/10min. Tasnee PP H3030 is designed for Bi-axial Oriented Polypropylene (BOPP) film applications, offering excellent transparency and gloss, high stiffness and excellent processability. Tasnee PP H3030 is formulated to be used for both general purpose and metallized films.

Tasnee PP H3030T is a Polypropylene Homopolymer with a Melt Flow Rate (MFR) of 3.0 g/10min. Tasnee PP H3030T is designed for Bi-axial Oriented Polypropylene (BOPP) film applications, offering excellent transparency and gloss, high stiffness and excellent processability. Tasnee PP H3030T is designed for High Speed Bi-axial Oriented Polypropylene (BOPP) film lines. Tasnee PP H3030T is formulated to be used for both general purpose and metallized films.

TRECORA POLYETHYLENE WAX – CWP400 is a High Density Polyethylene Wax intended for use in specifically Hot melt adhesives intended for the packaging industry where heat stability and heat resistance are required.

FULXUS® FX-SB-140 is used by changing the base resin from SEBS to SBS, low cost products can be manufactured. However, it has low weather resistance, and therefore it is not suitable for outdoor use.

Adiplast Wax AD - 70 is polyethylene wax used in adhesive manufacturing.

TRECORA POLYETHYLENE WAX – CWP400 E is a High Density Polyethylene Wax intended for use in general purpose Hot melt adhesives to reduce viscosity and control open and set times.

NIPLENE T40 contains characteristics called Homopolymer.

3.5 MELT FLOW HOMOPOLYMER FOR STRETCHED TAPE APPLICATIONS Pinnacle Polymers Polypropylene 1703 is made via UNIPOL™ PP technology, which utilizes gas-phase fluidized bed reactors with a high activity catalyst system to ensure uniform physical properties and lot-to-lot consistency.This product is intended for woven products used for carpet backing, sacking, industrial and geotextile fabrics.The 1703 product provides: Excellent color and processing stability Resistance to gas fading Low water carry-over Excellent lot-to-lot consistency Pinnacle's polypropylene, as marketed by Pinnacle Polymers, in natural, uncolored pellet form complies with appropriate requirements of CFR Title 21, Part 177, Subpart B, Section 177.1520 (c) 1.1a entitled "Olefin Polymers" of the Food Additives Amendment of 1958 to the United States Food, Drug and Cosmetic Act of 1938.

Marcus Oil and Chemical M200 is a low molecular weight polyethylene wax which comes in in liquid, pastille, flake and powder form for convenience of use.

KELAILI® PE WAX KL-10 is widely used in pipes, inks, coatings, cable fillings, hot metal products and textile processing industries.

FRGEL®E900 is a polyethylene wax based specialty additive, FRGEL®E900 is generally recommended for variety of coatings and inks application.

UltraPly™ TPO Flex Adhered is a flexible Thermoplastic Polyolefin roofing membrane produced with polyester weft-inserted reinforcement designed specifically for adhered installations. UltraPly TPO Flex Adhered membrane meets or exceeds all requirements for ASTM D 6878 Specification. This reflective, heat weldable TPO membrane is available in 60 mil (1.52 mm) thickness and is suitable for a variety of low-slope adhered roofing applications.