Products in Electrical & Electronics: Prepreg

AtenPly GPP35 are thin sheets of continuous reinforcement fibers impregnated with thermoplastic resin. It is made direct from the fiber roving and thermoplastic melt using proprietary technology developed by Jonam Composites Ltd. This cost-effective efficient process produces light weight, high-strength ,well impregnated, smooth tape with unidirectional fiber reinforcement.

370HR laminates and prepregs, deigned by Polyclad, are made using a patented high performance 180°C Tg FR-4 multifunctional epoxy resin system that is designed for multilayer Printed Wiring Board (PWB) applications where maximum thermal performance and reliability are required. We manufacture 370HR laminates and prepregs with high quality E-glass glass fabric for superior Conductive Anodic Filament (CAF) resistance. 370HR provides superior thermal performance with low Coefficient of Thermal Expansion (CTE) and the mechanical, chemical and moisture resistance properties that equal or exceed the performance of traditional FR-4 materials. 370HR is used in thousands of PWB designs and has proven to be best in class for thermal reliability, CAF performance, ease of processing and proven performance on sequential lamination designs.

35N is a pure polyimide laminate and prepreg system for applications requiring high temperature performance. High Tg (250°C) results in low Z-direction expansion for resistance to PTH failure during PWB processing, and minimizes risk of latent PTH defects in-service. Reduced temperature and time to cure offers improved throughput compared to traditional polyimide cycles.

AX-5110 is a flame retardant laminates, honeycomb and foam panels.

CM 15 is a Visual composites, Semi Structural and Fast Isothermally Press Curable, Class A Surface quality for painting, Hot Demoldable, Improved UV and environmental resistance, Improved fiber imprinting resistance

APCM SG 4528-040CU-103V is a heavy weight, conductive, surfacing film composed of a non-woven metallic copper mesh impregnated with a toughened epoxy resin plus an ultra lightweight veil for outstanding surfacing capability. It is designed for lightning and shielding protection of aircraft, equipotential ground planes and as a counterpoise for antenna installations.

Resinoid 1360HR is a glass reinforced, two-step phenolic molding compound. It exhibits outstanding impact strength, electrical and thermal properties. It is particularly suitable for high temperature and strength applications. This material comes in pelletized from and is suitable for transfer or compression molding. It can be preformed on automatic equipment.

Resinoid 1505 is a milled glass reinforced, two-step phenolic molding compound offering good mechanical and electrical properties. This product has been specifically formulated for electrical applications where very low post-molded shrinkage is desired. This material comes in granular form and is suitable for injection, transfer or compression molding. It can be preformed on automatic equipment.

85N is the ultimate polyimide and laminate prepreg system fo PWB's requiring resistance to high temperature, both in process and in end-use applications. Bromine-free chemistry provides Bestin-Class thermal stability for applications with sustained high in-use temperatures as well as for use in lead-free soldering applications.

Lectromat Glass Cloth and Mats 96-193 is applied in coil consolidation.

TerraGreen® is engineered for such high-performance applications as power amplifier boards for LTE base stations, internet infrastructure and cloud computing. TerraGreen ® features a Dielectric Constant (Dk) that is stable between -55°C and 125°C, up to 20 GHz. TerraGreen® is a lead-free assembly material and is easy to process. This high-performance material utilizes a short-lamination cycle; the product is easy to drill, does not require plasma desmear, and the prepreg shelf life is similar to FR-4 materials. TerraGreen® is suitable for high-layer count, high-speed digital backplanes and is compatible with Isola’s FR-4 materials for hybrid designs. TerraGreen® meets UL 94 V-0 and is halogen free.

APCM DA 4518 E-Glass is a modified epoxy system coated on heavy weight unidirectional E-Glass fibers. This product is designed to build excellent unidirectional strength using a minimum number of plies. DA 4518/E-Glass Uni also features extended room temperature out time and service temperatures to 300°F.

APCM DA 409U/S2-glass is a tough, versatile, modified epoxy resin prepreg that cures at 250ºF. The S-2 glass is a Zentron High Strength fiber. Standard weight is 260g/m2 with a 38% resin content. Other weights and resin contents available upon request.

APCM SG 4528-015CU-101V is a lightweight, conductive, surfacing film composed of a non-woven metallic copper mesh impregnated with a toughened epoxy resin plus an ultra lightweight veil for outstanding surfacing capability. It is designed for lightning and shielding protection of aircraft, equipotential ground planes and as a counterpoise for antenna installations.

Resinoid 1371 is a glass reinforced, two-step phenolic molding compound offering good mechanical and electrical properties. This product has been specifically formulated for applications requiring prolonged exposure to elevated temperatures andresistance to thermal shocks.This material comes in pelletized from and is suitable for injection, transfer or compression molding. It can be preformed on automatic equipment.

Natex P-Preg PLA P1/1 950 is a powder-coated fabric woven from flax fibers that are pre-impregnated with thermoplastic resins. It comes as NATTEX® P-Preg, PolyLactic Acid with 1000 mm Width and pre-preg fabrics uni-directional in natural fibers with flax of 900 g/m2.

Renegade Materials Corporation RM-5003 is a low dielectric and loss with high performance prepreg.

Resinoid 1382 is a glass reinforced, two-step phenolic molding compound formulated for applications requiring exceptional tensile strength. It has been used to replace cast aluminum in certain applications. Resinoid 1382 exhibits excellent dimensional stability, electrical and thermal properties. It is supplied in pelletized form for use in injection, transfer, and compression molding. It can be preformed on automatic equipment.

G200 has Blending Bismaleimide/Triazine (BT) and epoxy resin which provides G200 with enhanced thermal, mechanical and electrical performance over most epoxy materials. G200 possesses performance characteristics that make it an excellent selection for large panel size, high layer count Printed Wiring Boards (PWB).

Lectromat Glass Cloth and Mats WG-601-7 is applied in coil armor tape.

IS420 laminate and prepreg products are manufactured with a unique high performance multifunctional epoxy resin, reinforced with electrical grade (E-glass) glass fabric. This system provides improved thermal performance and low expansion rates in comparison to traditional FR-4 while retaining FR-4 processability. In addition to this superior thermal performance, the mechanical, chemical and moisture resistance properties all equal or exceed the performance of traditional FR-4 materials. The IS420 system is also laser fluorescing and UV blocking for maximum compatibility with Automated Optical Inspection (AOI) systems, optical positioning systems and photo imageable solder mask imaging.

Isola’s IS410 has a glass transition temperature (Tg) of 180°C and is specially formulated for superior performance through multiple thermal excursions, passing 6X solder tests at 288°C. IS410 is optimized for enhanced drilling performance allowing high aspect ratio holes of ≤10 mils. Its unique resin chemistry provides CAF resistance with the benefit of long-term reliability of boards built with small feature designs.

P25N consist of a polyimide resin system suitable for military, commercial or industrial electronic applications requiring superior performance and the utmost in thermal properties. These products utilize a polyimide and thermoplastic blend resin, fully cured without the use of Methylenedianiline (MDA). This results in a polymer with a high Tg without the characteristic difficulties of brittleness and low initial bond strength associated with traditional thermoset polyimides.

Lectromat Glass Cloth and Mats WG-204 is applied in permanent magnet bonding.

Aeroglide® is an epoxy-based composite surfacing film which can be oven or autoclave cured at either 250°F/120°C or 350°F/180°C to eliminate surface porosity for composite parts.

OM15 is for visual applications. It is translucent when cured without any white washes. It is Low Tg , about 110 °C.

APCM SG 4528-028AL-105V is a medium weight, conductive, surfacing film composed of a non-woven metallic aluminum mesh impregnated with a toughened epoxy resin plus an ultra light weight veil for outstanding surfacing capability. It is designed for lightning and shielding protection of aircraft, equipotential ground planes and as a counterpoise for antenna installations.

APCM DA 409U/G35-150 is a tough, versatile, modified epoxy resin prepreg that cures at 250°F, a standard modulus 150 g/m2 carbon prepreg tape which can also be supplied as a 200g/m2 or a 300 g/m2 prepreg.

Lectromat Glass Cloth and Mats DG-610 is applied in shrinkable coil armor tape.

84N is a high performance ceramic-filled polyimide prepreg based on Arlon’s 85N pure polyimide system, designed for use in filling etched areas in polyimide multilayers that contain thick copper layers and for filling clearance holes in metal cores. The ceramic filler in the resin serves to reduce shrinkage and inhibit crack formulation during through-hole drilling in filled clearance areas.

Natex P-Preg PP P1/1 900 is a powder-coated fabric woven from flax fibers that are pre-impregnated with thermoplastic resins. It comes as NATTEX® P-Preg, Polypropylene with 1000 mm Width and pre-preg fabrics uni-directional in natural fibers with flax of 900 g/m2.

Resinoid 1328 is a glass reinforced, two-step phenolic molding compound. It was specifically developed for applications requiring exceptional tensile strength such as grinding wheels. Resinoid 1328 exhibits excellent electrical and thermal properties as well as dimensional stability. This material comes in pelletized from and is suitable for injection, transfer or compression molding. It can be preformed on automatic equipment.

AtenPly CPPS35 are thin sheets of continuous reinforcement fibers impregnated with thermoplastic resin. It is made direct from the fiber roving and thermoplastic melt using proprietary technology developed by Jonam Composites Ltd. This cost-effective efficient process produces light weight, high-strength ,well impregnated, smooth tape with unidirectional fiber reinforcement.

AX-5170 is a cyanate ester carbon prepreg.

33N is a flame retardant (UL94 V-O) polyimide laminate and prepreg system where the excellent high performance properties of polyimide need to be combined with flame retardance. High Tg (250°C) results in low overall z-axis expansion, and minimizes risk of latent PTH defects in-service.

Lectromat Glass Cloth and Mats 95-147 is applied in bearing insulation.